Remove the rear differential solenoid valve connector assembly (B).
5.
Oil Filler Plug and Drain Plug - Remove
1.
Remove the drain plug (A) with the sealing washer (B).
2.
Remove the oil filler plug (C) with the sealing washer (D).
6.
Rear Differential Subharness - Remove
1.
Disconnect the ground terminal (A).
2.
Remove the harness clip (B).
3.
Remove the harness bracket (C).
7.
Companion Flange - Remove
1.
Pry up the stake on the locknut (A) from the groove of the clutch guide, making sure the tab completely clears the groove to prevent damaging the clutch guide.
2.
Install the companion flange holder and the holder handle on the companion flange.
3.
Loosen the locknut (A) counterclockwise so its tab (B) comes out from the groove (C) in the clutch guide.
4.
Tighten the locknut (A) until its tab (B) aligns with the groove (C).
5.
Clean any dirt from inside the groove in the clutch guide, then loosen the locknut.
6.
Remove the locknut (A), the spring washer (B), the back-up ring (C), and the O-ring (D).
7.
Remove the companion flange (A) with a commercially available puller.
8.
Oil Pump Cover - Remove
1.
Remove the oil pump cover (A) and oil pump cover seal (B).
2.
Remove the inner rotor (C) and the outer rotor (D).
3.
Remove the fluid strainer (E) and the dowel pins (F).
9.
Oil Pump Case - Remove
1.
Remove the oil pump case (A).
2.
Remove the dowel pins (B).
10.
Differential Clutch Assembly - Remove
1.
Remove the baffle cover (A).
2.
Remove the differential clutch assembly (B).
11.
Oil Pump Body Assembly - Remove
1.
Remove the 32.3 mm shim (A).
2.
Remove the 94.6 mm shim (B).
3.
Remove the oil pump body assembly (C).
4.
Remove the dowel pins (D) and the O-ring (E).
12.
Rear Differential Solenoid Valve - Remove
1.
Remove the rear differential solenoid valve (A), the O-ring (B), and the square washer (C).
1.
Rear Differential Solenoid Valve - Install
1.
Apply rear differential fluid to a new O-ring (A).
2.
Install the rear differential solenoid valve (B) with the O-ring, and the square washer (C).
2.
Oil Pump Body Assembly - Install
1.
Apply rear differential fluid to a new O-ring (A).
2.
Install the dowel pins (B) with the O-ring.
3.
Install the oil pump body assembly (C).
4.
Install the 32.3 mm shim (D).
5.
Install the 94.6 mm shim (E).
3.
Differential Clutch Assembly - Install
1.
Install the differential clutch assembly (A).
2.
Install the baffle cover (B).
4.
Oil Pump Case - Install
1.
Remove the dirt and oil from the sealing surfaces.
2.
Apply liquid gasket (P/N 08717-0004, 08718-0003, or 08718-0009) evenly to the sealing surface.
3.
Install the component within 5 minutes of applying the liquid gasket. Make sure you seal the entire circumference of the bolt holes to prevent fluid leakage.
NOTE:
If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply the new liquid gasket.
Allow it to cure at least 30 minutes after assembly before filling the differential with recommended fluid.
4.
Install the dowel pins (A).
5.
Install the oil pump case (B).
6.
Torque the mounting bolts in a crisscross pattern in several steps.
5.
Oil Pump Cover - Install
1.
Install the fluid strainer (A) and the dowel pins (B).
2.
Install the inner rotor (C) and the outer rotor (D) with the "·" marks (E) facing the oil pump case side.
3.
Install the oil pump cover (F) with a new oil pump cover seal (G).
4.
Torque the mounting bolts in a crisscross pattern in several steps.
6.
Companion Flange - Install
1.
Set the companion flange (A) to the clutch guide shaft.
2.
Drive on the companion flange using the 41.8 mm oil seal driver.
3.
Check the length of clutch guide shaft as shown.
NOTE: Make sure to drive on the companion flange until 2 to 3 thread pitches of the clutch guide shaft appears.
4.
Apply rear differential fluid to the used locknut.
5.
Set the used locknut to the clutch guide shaft.
6.
Install the companion flange holder and the holder handle on the companion flange.
7.
Tighten the used locknut.
8.
Remove the used locknut, then remove the companion flange holder and the holder handle.
9.
Check the companion flange has been set to the bottom.
10.
Apply rear differential fluid to a new O-ring (A).
11.
Install the O-ring, a new back-up ring (B), the spring washer (C), and a new locknut (D).
NOTE: Be sure to install the spring washer in the direction shown.
12.
Install the companion flange holder and holder handle on the companion flange.
13.
Tighten the locknut to the specified torque.
Specified Torque:
108 N·m (11.0 kgf·m, 80 lbf·ft)
14.
Stake the locknut tab (A) into the groove in the clutch guide.
7.
Oil Filler Plug and Drain Plug - Install
1.
Install the drain plug (A) with a new sealing washer (B).
2.
Install the oil filler plug (C) with a new sealing washer (D) finger-tight.