Multipurpose Camera Aiming
Special Tools Required
Image Description/Tool Number
6379732.png Stand 07AAJ-TK8A100*
9586132.png Attachment Bracket 07AAK-5K0A110
5074667.png Stand Set 07AAJ-STKA220*
11061078.png Stand Pole 07AAK-5K0A120
11061120.png Target Set 070AK-TYPA030
11061138.png Target Holder Set 07AAB-TYPA020
*: Use Stand 07AAJ-TK8A100 or Stand Set 07AAJ-STKA220 for aiming.

NOTE:
The multipurpose camera unit must be re-aimed if the multipurpose camera unit or windshield is removed or replaced. The LKAS and ACC indicators (amber) will blink if the aiming process is not completed correctly. If any DTC is indicated, do the indicated DTC's troubleshooting first. If the DTC is not repaired, you cannot complete the multipurpose camera aiming procedure:
?
Dynamic Camera Aiming Incomplete: DTC B2A60-52
?
Static Camera Aiming Incomplete: DTC B2A60-54
Cautions for the operation environment:
?
Multipurpose camera aiming should be done on a flat place.
?
To aim the multipurpose camera, you need the following amount of open space in front of the vehicle: 7 m (23 ft) measured from the front bumper, 4 m (13 ft) wide, and 1.5 m (4.9 ft) height.
?
Make sure the vehicle is not facing any direct light source, as this will affect the static camera aiming.
?
Make sure there are no black and white checkered, or dark and light alternating patterns directly behind the targets as this will affect the static camera aiming.
Set up the vehicle:
?
Aiming the multipurpose camera requires the HDS.
?
Do not put any objects on the instrument panel.
?
Remove the all cargo from the vehicle except the tool kit.
?
Make sure that there are no stains, dust or dirt on the lens of the multipurpose camera unit, and the windshield area where the camera is mounted.
?
Make sure that all doors are closed.
?
Make sure the suspension has not been modified.
?
Make sure all the tire sizes are correct and that their pressure is correct.
?
Make sure the fuel tank is full.
?
Make sure the steering wheel is pointed straight ahead, and do not turn it after setting the vehicle.
?
Shift the transmission to P position, and apply the parking brake.
When marking on the floor, use suitable tape to mark the exact locations.

2. Multipurpose Camera - Static Camera Aim

Marking of the Target Position
1.
Measure and make a mark (Z1) in front of the vehicle 6,000 mm (236.22 in) from the center of the front wheels.




Special Tools Set-Up, Target Pattern Surface Height Adjustment, and Positioning:
2.
Set-up the target.
?1.
Install the stand pole (A) onto the stand (B).
NOTE: The stand pole 1,000 mm (39.37 in) is too low to align the multipurpose camera, and cannot be used for this procedure. You must use stand pole 07AAK-5K0A120.
?2.
Route the cord through the collar and place it on the aiming stand.

?3.
Install the attachment bracket (C) onto the stand pole.
?4.
Assemble the target holders (D).
3.
Install the target holder assemblies onto the attachment bracket (one on each side), with the target mounting holes (A) facing toward the vehicle.
NOTE: Make sure the horizontal poles are fully seated against the attachment bracket.
4.
Install the targets onto the horizontal poles.
5.
Check the height (950 mm (37.40 in)) of all three targets at the center mark (A). The center target should be the same height as the outer targets. If necessary, adjust the center target by moving the target adjuster up or down on the stand pole to match the heights of the outer targets.
6.
Place the aiming target assembly on the mark (Z1).
NOTE:
Make sure the target vertical poles (C) on the line (D).




Choose the Setting Value of the Multipurpose Camera Height:
7.
Measure the right and left front wheel arch height "H1" from the ground to the center of the wheel arch.
8.
Calculate the average value of the front wheel arch height "H2".
9.
Subtract the front wheel arch height standard value of 776 mm (30.55 in)*1, 786 mm (30.94 in)*2 "H3" from the average value of "H2".
*1: 2WD
*2: AWD
10.
Choose the setting value number (the multipurpose camera unit height setting value for the HDS) based on the calculation made from H2 minus H3 from the table below.
Setting value number
"H3" with ? or ? numerical value from the standard value
(1)
More than ?5 mm (0.20 in) to ?15 mm (0.59 in) or less
(2)
More than ?5 mm (0.20 in) to less than ?5 mm (0.20 in)
(3)
More than ?15 mm (0.59 in) to less than ?5 mm (0.20 in)
(4)
More than ?25 mm (0.98 in) to less than ?15 mm (0.59 in)
(5)
More than ?35 mm (1.38 in) to less than ?25 mm (0.98 in)
NOTE: The HDS uses this number when choosing the multipurpose camera unit height setting value.
Example
The front wheel arch height measurement value ''H1''
: Right front wheel arch height 775 mm (30.51 in)
: Left front wheel arch height 772 mm (30.39 in)
The front wheel arch height average value ''H2''
: (775 mm (30.51 in)?772 mm (30.39 in))/2=773.5 mm (30.45 in)
The difference between the measured value and the standard value "H3"
: 773.5 mm (30.45 in)?776 mm (30.55 in)(standard value) =?2.5 mm (?0.09 in)
The setting value number which corresponds to the numerical value (2).

NOTE: If the measured value exceeds ?15.0 mm (0.591 in) or ?35.0 mm (1.378 in), the multipurpose camera aiming will not work. Check for frame/suspension damage or modification.
11.
Apply the parking brake.
If the aiming has failed or is aborted, you must start the static camera aiming procedure again.
13.
Turn the vehicle to the ON mode, and turn the headlights off.




Implementation of the Static Camera Aiming
14.
In the DRIVING SUPPORT MENU, then INTEGRATED DRIVER SUPPORT SYSTEM, then ADJUSTMENT, then select Static Camera Aiming on the HDS. After the CAUTION SCREEN, the LKAS indicator blinks and "CAM" is displayed at the MID.
NOTE: The static camera aiming status can be confirmed indicator on the MID.
15.
Set the multipurpose camera unit height on the HDS.
NOTE: Use "The multipurpose camera unit height setting value number" which was recorded.
16.
Select "Target Middle" from the HDS. The CAM indicator on the MID begins to blink when issuing instructions.
NOTE:
The CAM indicator stops blinking and turns off when the aiming is completed. When the aiming fails, it turns on.
If the aiming has failed or is aborted, you must start the static camera aiming procedure again.
17.
Confirm the ''Target Middle'' on the HDS.
18.
Select "Target Left" from the HDS.
19.
Confirm "Target Left" on the HDS.
20.
Select "Target Right" from the HDS.
21.
Confirm "Target Right" on the HDS.
22.
Turn the vehicle OFF, then ON to the CONFIRMED SCREEN on the HDS.
23.
The static camera aiming status can be confirmed. Make sure the CAM indicator on the MID turns off:
If the CAM indicator is displayed in the MID, the aiming has not finished. If ERROR is displayed on the HDS, the aiming procedure was interrupted. Check for problems with the following detection Item.
If the static camera aiming is completed, go to the next step for the dynamic camera aiming procedure.

3. Multipurpose Camera - Dynamic Camera Aim

Precaution for the Dynamic Camera Aiming:
Carry out the dynamic camera aiming on a flat and straight road that has several lanes that will allow the vehicle to be driven at speeds between 45?70 mph (72?112 km/h) for 10 minutes or more.
You must complete the dynamic aiming within 30 minutes or the aiming will fail.
Poor weather such as rain, fog, or snow may prevent the camera from aiming.
Wet roads can also affect the aiming procedure if the yellow or white lines are not visible because of reflections caused by the water.
When you do the dynamic camera aiming in the dark, turn the headlights on and ensure that the windshield and headlights are clean.
If the dynamic camera aiming fails for some reason, an aiming failure code is displayed on the HDS. In this case, carry out the troubleshooting for the code indicated using the HDS.
When doing the aiming procedure, make sure you drive in the center of the lane and avoid using the windshield wipers or the turn signal.
1.
Turn the vehicle to the ON mode.
2.
Check the multipurpose camera unit DTCs with the HDS. Make sure that only DTC B2A60-52 indicated.
NOTE: The multipurpose camera aiming procedure can be done when this DTC is shown but if any other DTC is indicated, troubleshoot the DTC before continuing.
3.
In the DRIVING SUPPORT MENU, then INTEGRATED DRIVER SUPPORT SYSTEM, then ADJUSTMENT, then select Dynamic Camera Aiming on the HDS. "CAM" of the MID begins a blink when issuing instructions.
4.
Carry out the aiming according to the instructions indicated on the HDS screen. If the dynamic camera aiming fails for any reason, the HDS will display an aiming failure code. In this case, carry out the troubleshooting for the codes, then retry the aiming procedure.
NOTE: The dynamic camera aiming status can be confirmed indicator on the MID.
5.
Stop the vehicle after confirming that the aiming is done. Turn the vehicle to the OFF (LOCK) mode, then to the ON mode, and make sure the LKAS indicator and the CAM indicator do not appear on the MID. If any DTCs are indicated, troubleshoot the indicated DTC.
NOTE: The dynamic camera aiming status can be confirmed on the MID and LKAS indicator as follows. If "CAM" is displayed on the MID, the aiming is not finished. Do the dynamic camera aiming procedure again.
6.
Turn the vehicle to the OFF (LOCK) mode.
7.
Disconnect the HDS.

4. Aiming Failure Code Index

NOTE: When the aiming procedure fails, the ERROR indicator is displayed on the HDS.

When the Static Camera Aiming Fails:
Detection Item
Diagnostic Procedure
Multipurpose camera unit function failure.
Check the multipurpose camera unit DTCs with the HDS and do the indicated DTC troubleshooting. After the DTC has cleared, redo the aiming procedure.
The position of three targets (prescribed distance, height, or distance between the targets) are not correct.
After checking the following, do the aiming procedure again:
Check that the aiming target is installed correctly on the body center-line.
Check the prescribed distance.
Check the target height.
Multipurpose camera unit mounting angle/position not correct:
The target is not properly positioned.
The target is not horizontally set up.
The arrangement of three targets (middle, left side and right side) is not correct.
The multipurpose camera unit is not correctly installed.
There is cargo in the vehicle.
The tire pressure is not correct.
The vehicle inclined abnormally (modified or damaged suspension etc.).
After checking the following, do the aiming procedure again:
The vehicle and the target are correctly set up.
The multipurpose camera unit is correctly installed.
There is no additional items in the trunk.
The tire pressure is correct.
Check for modified or damaged suspension, if necessary check the wheel alignment.
The middle target cannot be detected:
The windshield or the multipurpose camera lens is dirty.
There is not enough light or there is a strong backlight.
There is a strong backlight behind the target such as the sun or strong shop lighting.
There is something on the dashboard that is reflecting in the windshield.
The target is not properly positioned.
The multipurpose camera unit malfunction.

The left target cannot be detected.

The right target cannot be detected.
After checking the following, do the aiming procedure again:
Check the prescribed distance.
Check the target height.
Check the distance between targets.
Make sure the multipurpose camera lens has a clear, unobstructed view of the target.
The quantity of lights to a target is insufficient.
After checking the following, do the aiming procedure again:
The target area should be made brighter so that a target may look clear.
The quantity of lights to a target is excess.
After checking the following, do the aiming procedure again:
The target area should be made darker so that a target may look clear.
Multipurpose camera unit temperature out of range.
After checking the following, do the aiming procedure again:
The multipurpose camera unit is beyond its normal operating temperature range of ?104 to 221 °F (?40 to 105 °C).

When the Dynamic Camera Aiming Fails:
Detection Item
Diagnostic Procedure
Multipurpose camera unit function failure.
Check the multipurpose camera unit DTCs with the HDS and do the indicated DTC troubleshooting. After the DTC has cleared, redo the aiming procedure.
Multipurpose camera unit mounting angle/position is not correct.
After checking the following, do the aiming procedure again:
The vehicle and the target are correctly set up.
The multipurpose camera unit is correctly installed.
There is no additional items in the trunk.
The tire pressure is correct.
Check for modified or damaged suspension, if necessary check the wheel alignment.
Multipurpose camera unit temperature out of range.
After checking the following, do the aiming procedure again:
The multipurpose camera unit is beyond its normal operating temperature range of ?104 to 221 °F (?40 to 105 °C).