|
DTC Advanced Diagnostics: SRS related DTCs
SRS Related DTCs
NOTE
|
|
Always check "How to troubleshoot the SRS system" and proceed along each "DTC Troubleshooting" procedure. |
|
|
Make sure the 12 volt battery is fully charged. If not, the results of tests may not be accurate. |
|
|
The SRS indicator will turn on when the 12 volt battery voltage becomes below 10 volts. |
|
|
The possible causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes. |
DTC 81-51, 81-52, 81-53: Internal Failure of the Front Passenger's Weight Sensor Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's weight sensor unit internal failure | | |
|
DTC 81-54: Short to Power in the Front Passenger's Weight Sensor Power Circuit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the front passenger's weight sensor unit and the front passenger's weight sensor (front inner side) (SWSP1 line) |
|
|
Short to power between the front passenger's weight sensor unit and the front passenger's weight sensor (rear inner side) (SWSP2 line) |
|
|
Short to power between the front passenger's weight sensor unit and the front passenger's weight sensor (front outer side) (SWSP3 line) |
|
|
Short to power between the front passenger's weight sensor unit and the front passenger's weight sensor (rear outer side) (SWSP4 line) | | |
|
DTC 81-55: Short to Ground in the Front Passenger's Weight Sensor Power Circuit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (front inner side) (SWSP1 line) |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (rear inner side) (SWSP2 line) |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (front outer side) (SWSP3 line) |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (rear outer side) (SWSP4 line) |
|
|
Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (front inner side) (SWSP1, SWSG1 lines) |
|
|
Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (rear inner side) (SWSP2, SWSG2 lines) |
|
|
Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (front outer side) (SWSP3, SWSG3 lines) |
|
|
Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (rear outer side) (SWSP4, SWSG4 lines) | | |
|
DTC 81-56: Internal Failure of the Front Passenger's Weight Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's weight sensor unit internal failure | | |
|
DTC 81-61, 84-81: Wrong Combination with the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's weight sensor unit internal failure |
|
|
SRS unit internal failure | | |
|
DTC 81-71: Front Passenger's Weight Sensor Output Check Failure DTC 84-92: Front Passenger's Weight Sensor Calibration Failure
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's weight sensor unit not initialized |
|
|
Front passenger's weight sensor unit improper initialization |
|
|
Front passenger's weight sensor unit internal failure | | |
|
DTC 82-11, 82-12: Internal Failure of the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front inner side)) | | |
|
DTC 82-13: No Signal From the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the front passenger's weight sensor unit and the front passenger's weight sensor (front inner side) (SWSP1 line) |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (front inner side) (SWSS1 line) |
|
|
Open, Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (front inner side) (SWSS1, SWSG1 lines) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front inner side)) | | |
|
DTC 82-21, 82-22: Internal Failure of the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear inner side)) | | |
|
DTC 82-23: No Signal From the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the front passenger's weight sensor unit and the front passenger's weight sensor (rear inner side) (SWSP2 line) |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (rear inner side) (SWSS2 line) |
|
|
Open, Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (rear inner side) (SWSS2, SWSG2 lines) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear inner side)) | | |
|
DTC 83-31, 83-32: Internal Failure of the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front outer side)) | | |
|
DTC 83-33: No Signal From the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the front passenger's weight sensor unit and the front passenger's weight sensor (front outer side) (SWSP3 line) |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (front outer side) (SWSS3 line) |
|
|
Open, Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (front outer side) (SWSS3, SWSG3 lines) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front outer side)) | | |
|
DTC 83-41, 83-42: Internal Failure of the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear outer side)) | | |
|
DTC 83-43: No Signal From the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the front passenger's weight sensor unit and the front passenger's weight sensor (rear outer side) (SWSP4 line) |
|
|
Short to ground between the front passenger's weight sensor unit and the front passenger's weight sensor (rear outer side) (SWSS4 line) |
|
|
Open, Short to another line between the front passenger's weight sensor unit and the front passenger's weight sensor (rear outer side) (SWSS4, SWSG4 lines) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear outer side)) | | |
|
DTC 84-91: Front Passenger's Weight Sensor Not Calibrated
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's weight sensor unit not initialized |
|
|
Front passenger's weight sensor unit improper initialization |
|
|
Front passenger's weight sensor unit internal failure | | |
|
DTC 84-93: Different Serial ID of the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front inner side)) | | |
|
DTC 84-94: Different Serial ID of the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear inner side)) | | |
|
DTC 84-95: Different Serial ID of the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front outer side)) | | |
|
DTC 84-96: Different Serial ID of the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear outer side)) | | |
| |