SRS DTC Troubleshooting: 41-1x
DTC 41-1x (''x'' can be 0 thru 9 or A thru F) : No Signal From the Left Front Impact Sensor
NOTE:
Before replacing the SRS unit, check the SRS unit software version with the HDS. If the software version is not the latest,
update the SRS unit software , and retest.
DTC (SRS)
1.
Problem verification:
Problem verification
?2.
Turn the vehicle to the ON mode, then wait for 10 seconds.
Is DTC 41-1x indicated?
The failure is duplicated. Go to step 2.
2.
Connector connection check:
Connector connection check
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Check the following connector connections.
SRS unit connector A (39P)
Left front impact sensor 2P connector (on the engine compartment wire harness)
Connector between the SRS unit and the left front impact sensor
Are the connectors OK?
3.
System check:
System check
?1.
Repair the poor connector connections whichever was the cause of the problem in step
2 .
?3.
Turn the vehicle to the ON mode, then wait for 10 seconds.
Is DTC 41-1x indicated?
Turn the vehicle to the OFF (LOCK) mode, then go to step 4.
The system is OK at this time.?
4.
Shorted wire check (LFS? line to LFS? line):
Shorted wire check (LFS? line to LFS? line)
?1.
Disconnect the negative cable from the 12 volt battery, then wait at least 3 minutes.
?2.
Disconnect the following connectors.
SRS unit connector A (39P)
Left front impact sensor 2P connector (on the engine compartment wire harness)
?3.
Measure the resistance between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
SRS unit connector A (39P): disconnected
Left front impact sensor 2P connector (on the engine compartment wire harness): disconnected
Test point 1
Test point 2
Is there an open circuit, or at least 1 M??
The LFS? and LFS? wires are not shorted. Go to step 5.
Short to another wire in the engine compartment wire harness or the dashboard wire harness; replace the faulty harness, then clear the DTC.?
5.
Shorted wire check (LFS?, LFS? lines):
Shorted wire check (LFS?, LFS? lines)
?1.
Measure the resistance between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
SRS unit connector A (39P): disconnected
Left front impact sensor 2P connector (on the engine compartment wire harness): disconnected
Test point 1
Test point 2
Body ground
Test point 1
Test point 2
Body ground
Is there an open circuit, or at least 1 M??
The LFS? and LFS? wires are not shorted. Go to step 6.
Short to ground in the engine compartment wire harness or the dashboard wire harness; replace the faulty harness, then clear the DTC.?
6.
Shorted wire check (LFS?, LFS? lines to power):
Shorted wire check (LFS?, LFS? lines to power)
?1.
Reconnect the negative cable to the 12 volt battery.
?2.
Turn the vehicle to the ON mode.
?3.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
SRS unit connector A (39P): disconnected
Left front impact sensor 2P connector (on the engine compartment wire harness): disconnected
Test point 1
Test point 2
Body ground
Test point 1
Test point 2
Body ground
Is there 0.2 V or less?
The LFS? and LFS? wires are not shorted to power. Go to step 7.
Short to power in the engine compartment wire harness or the dashboard wire harness; replace the faulty harness, then clear the DTC.?
7.
Open wire check (LFS?, LFS? lines):
Open wire check (LFS?, LFS? lines)
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Connect terminals A and B with a jumper wire.
Terminal A
Left front impact sensor 2P connector No. 1 (on the engine compartment wire harness)
Terminal B
Left front impact sensor 2P connector No. 2 (on the engine compartment wire harness)
?3.
Measure the resistance between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
SRS unit connector A (39P): disconnected
Left front impact sensor 2P connector (on the engine compartment wire harness): disconnected
Left front impact sensor 2P connector terminals No. 1 and No. 2 (on the engine compartment wire harness): jumped
Test point 1
Test point 2
Is there 1.0 ? or less?
Open in the engine compartment wire harness or the dashboard wire harness; replace the faulty harness, then clear the DTC.?