SRS DTC Troubleshooting: 46-1x | 2012-2016 CR-V RM1/RM4,RE5/RE6 HONDA CR-V Service Manual

SRS DTC Troubleshooting: 46-1x

DTC 46-1x (''x'' can be 0 thru 9 or A thru F): No Signal From the Right Side Impact Sensor (second)

NOTE:

	Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components, of the correct part number, and that they were properly installed.
	Before doing this troubleshooting procedure, review SRS Precautions and Procedures, General Troubleshooting Information, and 12 Volt Battery Terminal Disconnection and Reconnection.
	Before replacing the SRS unit, check the SRS unit software version with the HDS. If the software version is not the latest, update the SRS unit software, and retest.

DTC Description	DTC

DTC check:

DTC check

?1.	Clear the DTCs with the HDS.

?2.	Turn the vehicle to the ON mode, then wait for 10 seconds.

?3.

Check for DTCs with the HDS.

DTC Description	DTC

Are DTCs indicated?


	Only DTC 46-11

Go to step 2.


	DTC 46-1x (except 46-11)

Replace the right side impact sensor (second), then clear the DTC.?


	NO DTC

Intermittent failure, the system is OK at this time. Go to Troubleshooting Intermittent Failures. If another DTC is indicated, troubleshoot the DTC.?

Shorted wire check (RS2? line to RS2? line):

Shorted wire check (RS2? line to RS2? line)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.	Disconnect the negative cable from the 12 volt battery, then wait at least 3 minutes.

?3.

Disconnect the following connectors.

Right side impact sensor (first) 4P connector (on the floor wire harness)

Right side impact sensor (second) 2P connector (on the floor wire harness)

?4.

Measure the resistance between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	Right side impact sensor (first) 4P connector (on the floor wire harness): disconnected
	Right side impact sensor (second) 2P connector (on the floor wire harness): disconnected
Test point 1	Right side impact sensor (second) 2P connector No. 1 (on the floor wire harness)
Test point 2	Right side impact sensor (second) 2P connector No. 2 (on the floor wire harness)

Is there an open circuit, or at least 1 M??


	YES

The RS2? and RS2? wires are not shorted. Go to step 3.


	NO

Short to another wire in the floor wire harness between the right side impact sensor (first) and the right side impact sensor (second); replace the floor wire harness, then clear the DTC.?

Shorted wire check (RS2?, RS2? lines):

Shorted wire check (RS2?, RS2? lines)

?1.

Measure the resistance between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	Right side impact sensor (first) 4P connector (on the floor wire harness): disconnected
	Right side impact sensor (second) 2P connector (on the floor wire harness): disconnected
Test point 1	Right side impact sensor (second) 2P connector No. 2 (on the floor wire harness)
Test point 2	Body ground

Test point 1	Right side impact sensor (second) 2P connector No. 1 (on the floor wire harness)
Test point 2	Body ground

Is there an open circuit, or at least 1 M??


	YES

The RS2? and RS2? wires are not shorted. Go to step 4.


	NO

Short to ground in the floor wire harness between the right side impact sensor (first) and the right side impact sensor (second); replace the floor wire harness, then clear the DTC.?

Shorted wire check (RS2?, RS2? lines to power):

Shorted wire check (RS2?, RS2? lines to power)

?1.	Reconnect the negative cable to the 12 volt battery.

?2.	Turn the vehicle to the ON mode.

?3.

Measure the voltage between test points 1 and 2.

Test condition	Vehicle ON mode
	Right side impact sensor (first) 4P connector (on the floor wire harness): disconnected
	Right side impact sensor (second) 2P connector (on the floor wire harness): disconnected
Test point 1	Right side impact sensor (second) 2P connector No. 2 (on the floor wire harness)
Test point 2	Body ground

Test point 1	Right side impact sensor (second) 2P connector No. 1 (on the floor wire harness)
Test point 2	Body ground

Is there 0.2 V or less?


	YES

The RS2? and RS2? wires are not shorted to power. Go to step 5.


	NO

Short to power in the floor wire harness between the right side impact sensor (first) and the right side impact sensor (second); replace the floor wire harness, then clear the DTC.?

Open wire check (RS2?, RS2? lines):

Open wire check (RS2?, RS2? lines)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Connect terminals A and B with a jumper wire.

Terminal A	Right side impact sensor (first) 4P connector No. 1 (on the floor wire harness)
Terminal B	Right side impact sensor (first) 4P connector No. 4 (on the floor wire harness)

?3.

Measure the resistance between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	Right side impact sensor (first) 4P connector (on the floor wire harness): disconnected
	Right side impact sensor (second) 2P connector (on the floor wire harness): disconnected
	Right side impact sensor (first) 4P connector terminals No. 1 and No. 4 (on the floor wire harness): jumped
Test point 1	Right side impact sensor (second) 2P connector No. 1 (on the floor wire harness)
Test point 2	Right side impact sensor (second) 2P connector No. 2 (on the floor wire harness)

Is there 1.0 ? or less?


	YES

The RS2? and RS2? wires are OK. Replace the right side impact sensor (second), then clear the DTC, and retest. If the DTC is still present, replace the SRS unit.?


	NO

Open in the floor wire harness between the right side impact sensor (first) and the right side impact sensor (second); replace the floor wire harness, then clear the DTC.?