DTC Troubleshooting: U0230
DTC U0230: Gauge Control Module Lost Communication With PTG
DTC Description
DTC
U0230 Gauge control module lost communication with PTG
 

If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A.
If you have any loss of communication DTCs for the PCM, troubleshoot those DTCs first.
1.
Problem verification:

Problem verification
?1.
Clear the DTCs with the HDS.


?2.
Turn the vehicle to the OFF (LOCK) mode and then the ON mode.

?3.
Wait for at least 6 seconds.

?4.
Check for DTCs with the HDS.
DTC Description
DTC
U0230 Gauge control module lost communication with PTG
 

Is DTC U0230 indicated?

     
YES
     
     
     
Go to step 2.
     
NO
     
     
     
Intermittent failure, the system is OK at this time. Check for loose or poor connections.?
2.
Determine possible failure area (gauge control module power and ground, B-CAN line):

Determine possible failure area (gauge control module power and ground, B-CAN line)
?1.
Select B-CAN CONTROL UNITS INFORMATION from the BODY ELECTRICAL SYSTEM SELECT menu, and then select CHECK CONNECTED CONTROL UNITS.

?2.
Check the DETECT/NOT AVAILABLE information of the GAUGE CONTROL MODULE.

Is DETECT indicated?

     
YES
     
     
     
Go to step 8.
     
NO
     
     
     
Go to step 3.
3.
Fuse check:

Fuse check
?1.
Check the following fuse.
Fuse
No. B5 (10 A)
Location
Under-dash fuse/relay box

Is the fuse OK?

     
YES
     
     
     
Go to step 4.
     
NO
     
     
     
Replace the fuse. If the fuse blows again, repair a short to ground in the No. B5 (10 A) fuse circuit.?
4.
Open wire check (+B BACK UP line):

Open wire check (+B BACK UP line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Power tailgate control unit connector B (20P)

?3.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Power tailgate control unit connector B (20P): disconnected
Test point 1
Test point 2
Body ground

Is there battery voltage?

     
YES
     
     
     
The +B BACK UP wire is OK. Go to step 5.
     
NO
     
     
     
Repair an open or high resistance in the wire.?
5.
Open wire check (IG1 METER line):

Open wire check (IG1 METER line)
?1.
Disconnect the following connector.
Power tailgate control unit connector A (14P)

?2.
Turn the vehicle to the ON mode.

?3.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
Power tailgate control unit connector A (14P): disconnected
Power tailgate control unit connector B (20P): disconnected
Test point 1
Test point 2
Body ground

Is there battery voltage?

     
YES
     
     
     
The IG1 METER wire is OK. Go to step 6.
     
NO
     
     
     
Repair an open or high resistance in the wire.?
6.
Open wire check (GND lines):

Open wire check (GND lines)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Power tailgate control unit connector C (5P)

?3.
Check for continuity between test points 1 and 2 individually.
Test condition
Vehicle OFF (LOCK) mode
Power tailgate control unit connector A (14P): disconnected
Power tailgate control unit connector B (20P): disconnected
Power tailgate control unit connector C (5P): disconnected
Test point 1
Test point 2
Body ground

Test point 1
Test point 2
Body ground

Test point 1
Test point 2
Body ground

Is there continuity?

     
YES
     
     
     
The GND wires are OK. Go to step 7.
     
NO
     
     
     
Repair an open or high resistance in the ground wire or poor ground (G605).?
7.
Open wire check (B-CAN lines):

Open wire check (B-CAN lines)
?1.
Disconnect the following connector.
Gauge control module connector A (32P)

?2.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Power tailgate control unit connector A (14P): disconnected
Power tailgate control unit connector B (20P): disconnected
Power tailgate control unit connector C (5P): disconnected
Gauge control module connector A (32P): disconnected
Test point 1
Test point 2

Is there continuity?

     
YES
     
     
     
An open or poor connection in the B-CAN_L wire between the power tailgate control unit and the gauge control module.?
     
NO
     
     
     
An open or poor connection in the B-CAN_H wire between the power tailgate control unit and the gauge control module.?
8.
Open wire check (B-CAN lines):

Open wire check (B-CAN lines)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Gauge control module connector A (32P)
Power tailgate control unit connector A (14P)

?3.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Gauge control module connector A (32P): disconnected
Power tailgate control unit connector A (14P): disconnected
Test point 1
Test point 2

Is there continuity?

     
YES
     
     
     
An open or poor connection in the B-CAN_L wire between the power tailgate control unit and the gauge control module.?
     
NO
     
     
     
An open or poor connection in the B-CAN_H wire between the power tailgate control unit and the gauge control module.?