DTC Troubleshooting: U128D
DTC U128D: MICU Lost Communication With Gauge Control Module
DTC Description
DTC
U128D MICU Lost Communication With Gauge Control Module
 

NOTE: If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A.

NOTE: Refer to the Electrical Wiring Diagrams for the location of the under-dash fuse/relay box connectors.

1.
Problem verification:

Problem verification
?1.
Clear the DTCs with the HDS.


?2.
urn the vehicle to the OFF (LOCK) mode and then the ON mode.

?3.
Wait for at least 6 seconds.

?4.
Check for DTCs with the HDS.
DTC Description
DTC
U128D MICU Lost Communication With Gauge Control Module
 

Is DTC U128D indicated?

     
YES
     
     
     
Go to step 2.
     
NO
     
     
     
Intermittent failure, the system is OK at this time. Check for loose or poor connections.?
2.
Determine possible failure area (gauge control module power and ground, B-CAN line):

Determine possible failure area (gauge control module power and ground, B-CAN line)
?1.
Select GAUGES from the BODY ELECTRICAL SYSTEM SELECT menu, and then select DATA LIST.

Does the DATA LIST appear?

     
YES
     
     
     
Go to step 5.
     
NO
     
     
     
Go to step 3.
3.
Fuse check:

Fuse check
?1.
Check the following fuses.
Fuse
No. A29 (10 A)
Location
Under-hood fuse/relay box

Is each fuse OK?

     
YES
     
     
     
Go to step 4.
     
NO
     
     
     
Replace the fuse. If the fuse blows again, repair a short to ground in the No. A29 (10 A) fuse circuit.?
4.
Open wire check (+B BACK UP line):

Open wire check (+B BACK UP line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Gauge control module connector A (32P)

?3.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Gauge control module connector A (32P): disconnected
Test point 1
Test point 2
Body ground

Is there battery voltage?

     
YES
     
     
     
Repair an open or high resistance in the ground wire or poor ground (G502).?
     
NO
     
     
     
Repair an open or high resistance in the wire.?
5.
Open wire check (B-CAN_H lines):

Open wire check (B-CAN_H lines)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Under-dash fuse/relay box connector K (12P)
 

?3.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Gauge control module connector A (32P): disconnected
Under-dash fuse/relay box connector K (12P): disconnected
Test point 1
Test point 2

Is there continuity?

     
YES
     
     
     
The B-CAN_H wire is OK. Go to step 6.
     
NO
     
     
     
An open or poor connection in the B-CAN_H wire between the MICU and the gauge control module.?
6.
Open wire check (B-CAN_L lines):

Open wire check (B-CAN_L lines)
?1.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Gauge control module connector A (32P): disconnected
Under-dash fuse/relay box connector K (12P): disconnected
Test point 1
Test point 2

Is there continuity?

     
YES
     
     
     
The B-CAN_L wire is OK. Replace the gauge control module.?
     
NO
     
     
     
An open or poor connection in the B-CAN_L wire between the MICU and the gauge control module.?