DTC Troubleshooting: B1384
DTC B1384 : Tailgate Closer Unit Half Latch Switch Circuit Malfunction
DTC Description
DTC
B1384 Tailgate Closer Unit Half Latch Switch Circuit Malfunction
DTC (Power Tailgate Control Unit)
1.
Problem verification:
Problem verification
?1.
Clear the DTCs with the HDS.
Clear DTCs
?2.
Open the tailgate with the tailgate outer handle switch.
?3.
Close the tailgate manually.
?4.
Check for DTCs with the HDS.
DTC Description
DTC
B1384 Tailgate Closer Unit Half Latch Switch Circuit Malfunction
Is DTC B1384 indicated?
Intermittent failure, the system is OK at this time. Check for loose or poor connections between the power tailgate control unit and the power tailgate closer unit.?
2.
Determine possible failure area (PTG/PTL HALF line short, others):
Determine possible failure area (PTG/PTL HALF line short, others)
?1.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Tailgate Lock Sw. Half Latch
Is data list value ON?
3.
Determine possible failure area (power tailgate closer unit, others):
Determine possible failure area (power tailgate closer unit, others)
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Disconnect the following connector.
Power tailgate closer unit connector B (6P)
?3.
Turn the vehicle to the ON mode.
?4.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Tailgate Lock Sw. Half Latch
Is data list value ON?
4.
Shorted wire check (PTG/PTL HALF line):
Shorted wire check (PTG/PTL HALF line)
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Disconnect the following connector.
Power tailgate control unit connector A (14P)
?3.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode Power tailgate closer unit connector B (6P): disconnected Power tailgate control unit connector A (14P): disconnected
Test point 1
Test point 2
Body ground
Is there continuity?
Repair a short to ground in the wire.?
5.
Determine possible failure area (power tailgate closer unit, others):
Determine possible failure area (power tailgate closer unit, others)
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Disconnect the following connector.
Power tailgate closer unit connector B (6P)
?3.
Connect terminals A and B with a jumper wire.
Terminal A
Power tailgate closer unit connector B (6P) No. 4
Terminal B
Power tailgate closer unit connector B (6P) No. 6
?4.
Turn the vehicle to the ON mode.
?5.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Tailgate Lock Sw. Half Latch
Is data list value ON?
6.
Determine possible failure area (PTG/PTL HALF line, PTG/PTL SEG3 line):
Determine possible failure area (PTG/PTL HALF line, PTG/PTL SEG3 line)
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Disconnect the jumper wire.
?3.
Connect terminals A and B with a jumper wire.
Terminal A
Power tailgate closer unit connector B (6P) No. 4
Terminal B
Body ground
?4.
Turn the vehicle to the ON mode.
?5.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Tailgate Lock Sw. Half Latch
Is data list value ON?
7.
Open wire check (PTG/PTL SEG3 line):
Open wire check (PTG/PTL SEG3 line)
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Disconnect the jumper wire.
?3.
Disconnect the following connector.
Power tailgate control unit connector A (14P)
?4.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode Power tailgate closer unit connector B (6P): disconnected Power tailgate control unit connector A (14P): disconnected
Test point 1
Test point 2
Power tailgate closer unit connector B (6P) No. 6
Is there continuity?
Repair an open or high resistance in the wire.?
8.
Open wire check (PTG/PTL HALF line):
Open wire check (PTG/PTL HALF line)
?1.
Turn the vehicle to the OFF (LOCK) mode.
?2.
Disconnect the jumper wire.
?3.
Disconnect the following connector.
Power tailgate control unit connector A (14P)
?4.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode Power tailgate closer unit connector B (6P): disconnected Power tailgate control unit connector A (14P): disconnected
Test point 1
Test point 2
Power tailgate closer unit connector B (6P) No. 4
Is there continuity?
Repair an open or high resistance in the wire.?