Keyless/Power Door Locks/Security System (MICU, Door Multiplex Control Unit, and Front Passenger's Power Window Switch) Input Test
NOTE:
If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A.
Before testing, make sure the No. A2-2 (60 A) and No. A29 (10 A) fuse in the under-hood fuse/relay box are OK.
Before testing, make sure the No. B8 (15 A), No. B9 (15 A), No. B15 (10 A), No. B22 (7.5 A), No. B30 (10 A), No. B32 (15 A), No. B33 (15 A), No. 41 (20 A), No. B42 (20 A), and No. B44 (20 A) fuses in the under-dash fuse/relay box are OK.
Before testing, make sure the headlights, parking lights, taillights, turn signal lights, and horns are properly.
There are two pairs of fuses in the same circuit (No. B8 and No. B32 fuses, No. B9 and No. B33 fuses, and No. B15 and No. B30 fuses). If one fuse is blown, make sure to check the other fuse in the same circuit. If necessary, replace the blown fuse(s).

MICU

1.
Turn the vehicle to the OFF (LOCK) mode.

2.
Disconnect the following connectors.

Under-dash fuse/relay box connector B (44P)
Under-dash fuse/relay box connector C (38P)
Under-dash fuse/relay box connector D (32P)
Under-dash fuse/relay box connector N (13P)
Under-dash fuse/relay box connector P (20P)
Under-dash fuse/relay box connector R (8P)
Under-dash fuse/relay box connector S (10P)
Under-dash fuse/relay box connector W (24P)
Under-dash fuse/relay box connector X (10P)

3.
Inspect the connectors and socket terminals to be sure they are all making good contact:

If the terminals are bent, loose, or corroded, repair them as necessary, and recheck the system.
If the terminals look OK, go to step 4.

4.
With the connectors still disconnected, do the following input tests:

If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, go to step 5.

NOTE: These are door lock actuator operation tests for keyless entry.

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result
is not obtained
N10
PNK
Connect 12 volt battery power*1 and N10 (or N12), and terminal N12 (or N10) and ground with jumper wires
Check actuator operation:
The driver's door lock actuator should LOCK (or UNLOCK).
Faulty driver's door lock actuator
An open or high resistance in the wire
N12
GRY
S3
RED
Connect 12 volt battery power*1 and S3 (or S1), and terminal S1 (or S3) and ground with jumper wires
Check actuator operation:
The front passenger's door lock actuator should LOCK (or UNLOCK).
Faulty front passenger's door lock actuator
An open or high resistance in the wire
S1
YEL
B16
PNK
Connect 12 volt battery power*1 and B16 (or B11), and terminal B11 (or B16) and ground with jumper wires
Check actuator operation:
The left rear door lock actuator should LOCK (or UNLOCK).
Faulty left rear door lock actuator
An open or high resistance in the wire
B11
PUR
B18
LT GRN
Connect 12 volt battery power*1 and B18 (or B9), and terminal B9 (or B18) and ground with jumper wires
Check actuator operation:
The right rear door lock actuator should LOCK (or UNLOCK).
Faulty right rear door lock actuator
An open or high resistance in the wire
B9
YEL
B7*2
YEL
Connect 12 volt battery power*1 and B7 with a jumper wire
Check actuator operation:
The tailgate release actuator should work.
Faulty tailgate release actuator
Poor ground (G603) or an open in the ground wire
An open or high resistance in the wire
P11*3
GRY
Disconnect the keyless access control unit connector C (24P)
Check for continuity between terminal P11 and keyless access control unit connector C (24P) terminal No. 6:
There should be continuity.
An open or high resistance in the wire
*1: Use a fused jumper wire with an appropriate amperage fuse.
*2: Without power tailgate
*3: With keyless access system

5.
Reconnect the connectors to the driver's under-dash fuse/relay box; do the following input tests:

If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, the MICU must be faulty; replace the under-dash fuse/relay box (includes the MICU).*1
If all the input tests prove OK, go to step 6.*2

*1: Without door multiplex control unit
*2: With door multiplex control unit

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result
is not obtained
D17
RED
Under all conditions
Measure the voltage to ground:
There should be battery voltage.
Blown No. A29 (10 A) fuse in the under-hood fuse/relay box
An open or high resistance in the wire
D2
BLU
Under all conditions
Measure the voltage to ground:
There should be battery voltage.
Blown No. A2-2 (60 A) fuse in the under-hood fuse/relay box
An open or high resistance in the wire
W6
BLK
In all ignition switch positions or all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G501)
An open or high resistance in the ground wire
B32
BLK
In all ignition switch positions or all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G604)
An open or high resistance in the ground wire
B20
BLK
In all ignition switch positions or all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G604)
An open or high resistance in the ground wire
D10
BRN
In all ignition switch positions or all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G402)
An open or high resistance in the ground wire
R7
BLK
In all ignition switch positions or all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G501)
An open or high resistance in the ground wire
C27*1
LT BLU
Hood closed
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty security hood switch
Poor ground (G402) or an open in the ground wire
An open or high resistance in the wire
Hood open
Measure the voltage to ground:
There should be about 5 V.
Faulty security hood switch
A short to ground in the wire
B40
GRN
Driver's door open
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door switch
Faulty driver's door switch ground
An open or high resistance in the wire
Driver's door closed
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door switch
A short to ground in the wire
B29
BRN
Front passenger's door open
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty front passenger's door switch
Faulty front passenger's door switch ground
An open or high resistance in the wire
Front passenger's door closed
Measure the voltage to ground:
There should be about 5 V.
Faulty front passenger's door switch
A short to ground in the wire
B33
WHT
Left rear door open
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty left rear door switch
Faulty left rear door switch ground
An open or high resistance in the wire
Left rear door closed
Measure the voltage to ground:
There should be about 5 V.
Faulty left rear door switch
A short to ground in the wire
B34
GRY
Right rear door open
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty right rear door switch
Faulty right rear door switch ground
An open or high resistance in the wire
Right rear door closed
Measure the voltage to ground:
There should be about 5 V.
Faulty right rear door switch
A short to ground in the wire
W5
BLU
Left rear door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty left rear door lock knob switch
Poor ground (G601) or an open in the ground wire
An open or high resistance in the wire
Left rear door lock knob switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty left rear door lock knob switch
A short to ground in the wire
W4
ORN
Right rear door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty right rear door lock knob switch
Poor ground (G604) or an open in the ground wire
An open or high resistance in the wire
Right rear door lock knob switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty right rear door lock knob switch
A short to ground in the wire
W23
LT GRN
Tailgate outer handle switch pressed
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty tailgate outer handle switch
Poor ground (G603) or an open in the ground wire*2
Power tailgate control unit*3
An open or high resistance in the wire
Tailgate outer handle switch released
Measure the voltage to ground:
There should be about 5 V.
Faulty tailgate outer handle switch
A short to ground in the wire
B22
PNK
Tailgate open
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty tailgate latch switch
Poor ground (G603) or an open in the ground wire*2
Power tailgate control unit*3
An open or high resistance in the wire
Tailgate closed
Measure the voltage to ground:
There should be about 5 V.
Faulty tailgate latch switch
A short to ground in the wire
D22
GRN
Transmission range switch in P
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty or improperly adjusted transmission range switch
Poor ground (G101) or an open in the ground wire
An open or high resistance in the wire
Transmission range switch in any other position than P
Measure the voltage to ground:
There should be about 5 V.
A short to ground in the wire
Faulty or improperly adjusted transmission range switch
P11*4
GRY
Ignition key inserted into the ignition key cylinder
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty ignition key switch
Poor ground (G502) or an open in the ground wire
An open or high resistance in the wire
Ignition key removed from the ignition key cylinder
Measure the voltage to ground:
There should be about 5 V.
Faulty ignition key switch
A short to ground in the wire
X7*5
GRY
Driver's door lock switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door lock switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door lock switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door lock switch
A short to ground in the wire
X8*5
GRN
Driver's door lock switch in LOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door lock switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door lock switch in UNLOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door lock switch
A short to ground in the wire
X9*5
BRN
Driver's door key cylinder switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door key cylinder switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door key cylinder switch in neutral or LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door key cylinder switch
A short to ground in the wire
X10*5
PNK
Driver's door key cylinder switch in LOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door key cylinder switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door key cylinder switch in neutral or UNLOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door key cylinder switch
A short to ground in the wire
X4*5
WHT
Driver's door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door lock knob switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door lock knob switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door lock knob switch
A short to ground in the wire
X5*5
LT GRN
Driver's door lock knob switch in LOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door lock knob switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door lock knob switch
A short to ground in the wire
W10*5
LT BLU
Front passenger's door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Front passenger's door lock knob switch
Poor ground (G503) or an open in the ground wire
An open or high resistance in the wire
Front passenger's door lock knob switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Front passenger's door lock knob switch
A short to ground in the wire
W8*5
ORN
Front passenger's door lock switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty front passenger's door lock switch
Poor ground (G503) or an open in the ground wire
An open or high resistance in the wire
Front passenger's door lock switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty front passenger's door lock switch
A short to ground in the wire
W7*5
LT GRN
Front passenger's door lock switch in LOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty front passenger's door lock switch
Poor ground (G503) or an open in the ground wire
An open or high resistance in the wire
Front passenger's door lock switch in UNLOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty front passenger's door lock switch
A short to ground in the wire
*1: With security system
*2: Without power tailgate
*3: With power tailgate
*4: Without keyless access system
*5: Without door multiplex control unit

Door Multiplex Control Unit

6.
Turn the vehicle to the OFF (LOCK) mode.

7.
Disconnect the following connector.

Power window master switch 37P connector
8.
Inspect the connector and socket terminals to be sure they are all making good contact.

If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, go to step 9.

9.
With the connector still disconnected, do the following input tests:

If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, go to step 10.

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result
is not obtained
36
GRY
Disconnect these connectors:
Front passenger's power window switch 37P connector
Moonroof control unit/motor 14P connector
Check for continuity between terminal No. 36 and front passenger's power window switch 37P connector terminal No. 34:
There should be continuity.
An open in the LIN (P/W) wire
Check for continuity between terminal No. 36 and Moonroof control unit/motor 14P connector terminal No. 12:
There should be continuity.
An open in the LIN (P/W) wire
Check for continuity to ground:
There should be no continuity.
A short to ground in the LIN (P/W) wire

10.
Reconnect the connector, do the following input tests:

If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, go to step 11.

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result
is not obtained
26
RED
Under all conditions
Measure the voltage to ground:
There should be battery voltage.
Blown No. A29 (10 A) fuse in the under-hood fuse/relay box
Faulty under-dash fuse/relay box
An open or high resistance in the wire
25
PNK
Vehicle ON mode
Measure the voltage to ground:
There should be battery voltage.
Blown No. B22 (7.5 A) fuse in the under-dash fuse/relay box
An open or high resistance in the wire
4
WHT
Under all conditions
Measure the voltage to ground:
There should be battery voltage.
Blown No. B42 (20 A) fuse in the under-dash fuse/relay box
An open or high resistance in the wire
3
BLK
In all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G501)
An open or high resistance in the ground wire
31
BLK
In all power modes, disconnect the driver's power window motor 6P connector
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G501)
An open or high resistance in the ground wire
34
BRN
Driver's door key cylinder switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door key cylinder switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door key cylinder switch in neutral or LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door key cylinder switch
A short to ground in the wire
35
PNK
Driver's door key cylinder switch in LOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door key cylinder switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door key cylinder switch in neutral or UNLOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door key cylinder switch
A short to ground in the wire
33
LT GRN
Driver's door lock knob switch in LOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door lock knob switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door lock knob switch
A short to ground in the wire
32
WHT
Driver's door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Faulty driver's door lock knob switch
Poor ground (G501) or an open in the ground wire
An open or high resistance in the wire
Driver's door lock knob switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Faulty driver's door lock knob switch
An open or high resistance in the wire

Front Passenger's Power Window Switch

11.
Turn the vehicle to the OFF (LOCK) mode, open and close the driver's door.

12.
Disconnect the following connector.

Front passenger's power window switch 37P connector
13.
Inspect the connector and socket terminals to be sure they are all making good contact.

If the terminals are bent, loose, or corroded, repair them as necessary, and recheck the system.
If the terminals look OK, go to step 14.

14.
With the connector still disconnected, do the following input tests:

If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, go to step 15.

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result is not obtained
34
BLK
Disconnect these connectors:
Power window master switch 37P connector
Moonroof control unit/motor 14P connector
Check for continuity between terminal No. 34 and power window master switch 37P connector terminal No. 36:
There should be continuity.
An open in the LIN (P/W) wire
Check for continuity between terminal No. 34 and moonroof control unit/motor 14P connector terminal No. 12:
There should be continuity.
An open in the LIN (P/W) wire
Check for continuity to ground:
There should be no continuity.
A short to ground in the LIN (P/W) wire

15.
Reconnect the connector, do the following input tests:

If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, go to step 16.

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result is not obtained
4
BLK
Under all conditions
Measure the voltage to ground:
There should be battery voltage.
Blown No. B44 (20 A) fuse in the under-dash fuse/relay box
An open or high resistance in the wire
3
BLK
In all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G503)
An open or high resistance in the ground wire
29
LT BLU
Front passenger's door lock knob switch in UNLOCK
Measure the voltage to ground:
There should be less than 0.2 V.
Front passenger's door lock knob switch
Poor ground (G503) or an open in the ground wire
An open or high resistance in the wire
Front passenger's door lock knob switch in LOCK
Measure the voltage to ground:
There should be about 5 V.
Front passenger's door lock knob switch
A short to ground in the wire

16.
If multiple failures are found on more than one control unit, replace the under-dash fuse/relay box (includes the MICU). If input failures are related to a particular control unit, replace the control unit.