Insert a 6.0 mm (0.236 in) pin (A) into the positioning holes (B).
NOTE: Use only a 6.0 mm (0.236 in) pin with no burrs.
3.
Remove the shift cable end nut (C).
4.
Unlock the retainer lock (A).
5.
Rotate the socket holder retainer (A) in arrow direction (B) until it stops, and push the retainer lock (C) into the socket holder retainer to lock the retainer.
6.
Slide the socket holder (A) away as shown to remove the shift cable (B).
NOTE: Do not remove the shift cable by pulling the shift cable guide (C).
5.
Shift Lever - Remove
1.
Disconnect the connector.
2.
Remove the shift lever assembly.
6.
Shift Lever Bracket Base - Remove
1.
Shift Lever Bracket Base - Install
NOTE: Tighten the bolts and the nut in the sequence shown.
2.
Shift Lever - Install
1.
Install the shift lever assembly.
2.
Connect the connector.
3.
Shift Cable - Adjust
1.
Push the shift cable (A) until it stops, then release it.
NOTE: Do not hold the shift cable guide (B) to adjust the shift cable.
2.
Pull the shift cable back one step from the P position so that the shift position is in R.
3.
Turn the vehicle to the ON mode.
4.
Check that the R position indicator comes on.
5.
Turn the vehicle to the ACCESSORY mode.
4.
Shift Cable (Shift Lever Side) - Install
1.
Shift the shift lever to R.
2.
Insert a 6.0 mm (0.236 in) pin (A) into the positioning holes (B).
NOTE: Use only a 6.0 mm (0.236 in) pin with no burrs.
3.
Unlock the retainer lock (A).
4.
Rotate the socket holder retainer (A) in arrow direction (B) until it stops to create clearance (C) between the socket holder (D) and holder retainer, and push the retainer lock (E) into the socket holder retainer to lock the retainer.
5.
Align the shift cable slot (A) between the socket holder (B) and the socket holder retainer (C) with the opening (D).
6.
Slide the socket holder into the shift cable bracket (E) while installing the shift cable end (F) over the mounting stud (G) by aligning its square hole (H) with the square fitting (I) at the bottom of the stud.
NOTE:
Do not install the shift cable by holding the shift cable guide (J).
When the socket holder is installed in the shift cable bracket, the retainer lock is unhinged and releases the holder retainer lock, then the holder retainer returns under spring force to secure the shift cable.
7.
Push the retainer lock (A) fully to lock the socket holder retainer (B), and make sure that the retainer lock fits into the hinged-joint (C). If the retainer lock does not fit with the edge of the hinged-joint, rotate the holder retainer clockwise while pushing the retainer lock until it locks.
8.
Make sure that the shift cable end (A) is properly installed on the mounting stud (B).
If the cable end is out of position with the mounting stud, remove the shift cable from the shift cable bracket, then reinstall the cable end over the mounting stud before reinstalling the shift cable to the shift cable bracket. Do not install the shift cable end on the mounting stud with the shift cable install on the shift cable bracket.
If the shift cable end does not ride at the bottom of the mounting stud, rotate the stud to align the square fitting with the hole.
9.
Install the shift cable end nut (A).
10.
Remove the 6.0 mm (0.236 in) pin (B) that was installed to hold the shift lever.
5.
Shift Lever - After Install Check
1.
Turn the vehicle to the ON mode.
2.
Shift the transmission to each position/mode, and check that the A/T gear position indicator follows the shift lever operation.
3.
Check that the back-up lights come on when the transmission is in R position/mode.
4.
Check that the engine starts when the transmission is in P or N position/mode, and does not start in any other positions/modes.
5.
Shift the transmission to P position/mode.
6.
Check that the shift lock works properly. Push the shift lock release, and check that the shift lever releases, and also check that the shift lever locks when it is shifted back to P position/mode.
